Three-CCD camera

From Wikipedia, the free encyclopedia
Jump to navigation Jump to search
A beam splitter prism assembly, with a white beam entering the front, exiting the three focal-plane faces, filtered to produce red, green and blue.
A Philips type trichroic beam splitter prism schematic, with a different color separation order than the assembly shown in the photo. The red and blue beams each undergo one total internal reflection at the air gap and air/glass boundary respectively, while the other reflections are dichroic. This construction has the advantage over the above type that all 3 separated images are laterally inverted (as with a single sensor). In the first type, the blue image is not laterally inverted but the other two are.
A 3CCD imaging block consisting of a color separation prism of Philips type on which 3 CCDs are mounted.

A three-CCD (3CCD) camera is a camera whose imaging system uses three separate charge-coupled devices (CCDs), each one receiving filtered red, green, or blue color ranges. Light coming in from the lens is split by a complex prism into three beams, which are then filtered to produce colored light in three color ranges or "bands". The system is employed by high quality still cameras, telecine systems, professional video cameras and some prosumer video cameras.

Compared to cameras with only one CCD, three-CCD cameras generally provide superior image quality by using full-frame dichroic filters to better separate the red, green and blue color bands, and better low-light performance. By separating red, green, and blue color ranges with a 1:1 pixel ratio (known as "4:4:4"), three-CCD cameras achieve much better precision than single-CCD cameras.[1]

In contrast, almost all single-CCD cameras use a Bayer filter, using less accurate dye filters in front of each pixel to separate the colors. Because each pixel on a single CCD sensor is covered with its own tiny color filter, a frame is necessary to keep the dye filters from leaking into adjacent pixels. The result is less light absorbed compared to a CCD without a Bayer filter. Typically there is a 2:1 ratio of green and red/blue pixels, producing less color detail.[2]

Three-CCD cameras are more expensive than single-CCD cameras because they use three sensors rather than one, and because they use a beam splitter to drive each of the three CCD chips. Additionally most 3CCD cameras use higher quality but more expensive dichroic filters to separate the color bands.

The practice of cameras using three separate colors for color reproduction dates back to the advent of color photography, when three glass plates covered with photographic emulsion were used beginning in the late nineteenth century.

Now that (C)MOS (MOS = "metal oxide semiconductor") sensors are sufficiently advanced to compete with CCD technology, the catch-all term "three-chip" has arisen to cover all cameras that use beam splitters and three sensors for color reproduction. Previously, CCD sensors were superior to MOS in areas like image noise and sensitivity, and the ability to operate with global shutter.

Prior to CCD technology, color cameras used vacuum tube sensors for both color and monochrome. Because of mechanical tolerances and electrical changes as electronic components aged, 3-tube cameras had to be adjusted for image registration before each use. Each pixel in a CCD imager is fixed, so each of the three CCD elements on a 3CCD camera are registered in the factory, and permanently glued onto the optical block, thus eliminating any need for manual alignment (registration) by the end user.


Those with an elementary understanding of optics often wrongly assume that the prism assembly in the optical block bends light by refraction into the different colors, as a dispersive prism does. In fact the type of prism used for 3-chip cameras is used only as a beam splitter. Each of the three resulting beams still contain all visible colors, just as complex prisms in binoculars and single-lens reflex cameras also pass the entire visible spectrum. Optical filters are what separate the full spectrum into three sub-spectra (not just primary colors) for color reproduction.

The notion that a larger single sensor is as good as a 3-chip system is less-than-true due to two main factors: The first is that current Bayer filter designs use absorptive dye filters, which are inferior to dichroic filters in terms of color purity. The second is that current Bayer filter designs collect significantly less red and blue information than green, resulting in 1/4 the color resolution of 3-chip sensors. These limitations could possibly be overcome by using many tiny dichroic filters, and by designing Bayer filter matrices with equal numbers of red, green and blue pixels. However none currently exist.

See also


  1. ^ "3CCD colour advantages -AT". Retrieved 11 April 2018. 
  2. ^ Cliff Wootton (2005). A Practical Guide to Video and Audio Compression: From Sprockets and Rasters to Macroblocks. Elsevier. p. 137. ISBN 978-0-240-80630-3. 
3 monochrome sensors and color separation prism from Sony DCR-VX100E camera

External links

  • Diagram of the Philips prism and variations
  • Prism-Based Color Separation for Professional Digital Photography
Retrieved from ""
This content was retrieved from Wikipedia :
This page is based on the copyrighted Wikipedia article "Three-CCD camera"; it is used under the Creative Commons Attribution-ShareAlike 3.0 Unported License (CC-BY-SA). You may redistribute it, verbatim or modified, providing that you comply with the terms of the CC-BY-SA